Pioneer BDR-2203 8x Blu-ray Disc Writer

DVD Write and ReWrite Tests - Nero Burning Rom 7.11.10.0 and Drag-to-Disc 5.20:

To test the DVD writing performance of Pioneer's new drive I used Verbatim 16x DVD+R, 16x DVD-R, 6x DVD-RW and 8x DVD+RW media. To get the writing times, a 4.38GB image was burned to our test discs using Nero.

When writing to DVD+R and DVD-R media at 16x, the BDR-2203 uses CAV. By looking at the screenshots above, you can see that Pioneer's new drive starts writing at about 6.7x and accelerates, reaching its maximum speed at the end of the disc.

The BDR-2203 also features 8x DVD+RW and 6x DVD-RW writing speeds. While the drive uses CLV when writing to DVD-RW media, it uses Z-CLV to reach its maximum DVD+RW writing speed.

The BDR-2203 performed very well in our DVD writing tests. While not as fast as some of the 22x and 24x DVD writers we've looked at recently, it turned in some impressive times with DVD±R and DVD±RW media.

While Pioneer has a list of supported media on its website, I wanted to see for myself how well the BDR-2203 worked with some of the DVD+R and DVD-R discs available in my area. The media types, along with the average time it took the drive to write our 4.38GB image, are listed below.

So what about writing quality? Testing a drive's DVD writing quality isn't easy. Until now, there were very few options, unless you wanted to shell out thousands of dollars for a certified test machine. Thanks to KProbe, we can test a disc's PI (Parity Inner) and PIF (Parity Inner Fail) rates. For these tests I used a Lite-On SOHW-1673S and read the discs at 4x with the PI and PIF ECC sums set to 8 and 1 respectively. For comparison, I also tested the discs on a BenQ DW1640. When combined with Nero CD Speed, the DW1640 is able to report PI Errors, PI Failures, Parity Outer Failures and even jitter levels. For this test, the discs are read at 8x with both the PI and PIF ECC sums set to 8.

So what are "good" results supposed to look like? With KProbe, the PI errors should not exceed 280 and the number of PIF errors should stay below 4. When testing with CD Speed, the number of PI errors should stay below 280 as well. However, because it scans with an ECC sum of 8, a higher number of PIF errors is acceptable, as long as they do not exceed 32. Since POF errors are uncorrectable, we really don't want to see any of them at all.

I also put these discs through a "stress test" by reading them back at 16x with the DW1640. By reading these discs back at this speed, we can see if there are any readability issues caused by the number of errors or high levels of jitter. 

The BDR-2203's writing quality was pretty good with most of the DVD+R media we tested. Aside from a few small spikes, the PI/PIF rates stayed within acceptable limits.

Lastly, here are some results from our DVD-R test media. While the writing quality varied from one manufacturer to another, the results were fairly good for the most part.

To test the BDR-2203's packet writing performance I used Drag-to-Disc 5.20. Verbatim 8x DVD+RW, Verbatim 6x DVD-RW and Maxell 5x DVD-RAM media were used once again.

The BDR-2203 performed fairly well in our packet writing tests. While not the fastest drive we've tested, it turned in some respectable times when reading and writing to DVD+RW, DVD-RW and DVD-RAM media.

Double Layer DVD Write Tests - Nero Burning Rom 7.11.10.0:

To test the double layer DVD writing performance of the BDR-2203, I used DVD+R DL and DVD-R DL media from Verbatim, Moser Baer and Memorex. I created about 8GB of random files and directories on my hard drive and then burned them to our test discs with Nero.

The BDR-2203 had no problems taking the top spot in this test. Thanks to its 8x writing speed, the drive took 15:51 to write 8001MB of data to DVD+R DL media and 16:38 to do the same with DVD-R DL discs. So what about writing quality? Take a look below.

The writing quality was pretty good with Verbatim's DVD+R DL and DVD-R DL media. The error rates stayed within acceptable limits and, aside from a dip at the layer change, there weren't any readability problems. Unfortunately, Memorex's DVD+R DL media didn't fair quite as well. Looking at the screenshots above, you can see that there was a large PI/PIF spike at the layer change. The worst results were with Moser Baer's DVD+R DL media. When tested with KProbe and CD Speed, the error rate was very high throughout the second layer of the disc.